Further prop questions

Eddie Batchelor perkinsrx at centurytel.net
Wed Nov 17 07:11:15 AKST 2004


I saw the 4 props Nat recently purchased. They were all 4 bladed props and
the hole was off center so much even my untrained eye could see it.   I
don't remember if it was all 4 or not ,,but do remember more than 1 being
off.

Eddie

-----Original Message-----
From: discussion-request at nsrca.org
[mailto:discussion-request at nsrca.org]On Behalf Of Dean Pappas
Sent: Wednesday, November 17, 2004 9:28 AM
To: discussion at nsrca.org
Subject: RE: Further prop questions


I can't say I've ever seen an APC with the hole off center, either.
Some require a bit of balancing, but most don't even need that, and
the ones that do require very little material to be removed.

Dean Pappas
Sr. Design Engineer
Kodeos Communications
111 Corporate Blvd.
South Plainfield, N.J. 07080
(908) 222-7817 phone
(908) 222-2392 fax
d.pappas at kodeos.com


-----Original Message-----
From: discussion-request at nsrca.org
[mailto:discussion-request at nsrca.org]On Behalf Of John Ferrell
Sent: Wednesday, November 17, 2004 10:13 AM
To: discussion at nsrca.org
Subject: Re: Further prop questions


I have not observed the problem you describe. Since I am naturally a little
paranoid, I wonder if you are really getting APC props or a counterfeit?

When I need to drill a really precise hole, I use and end mill for a bit.
Both the work and the tool must be held securely, but the result is a truly
round hole exactly where it needs to be. If tubing is used for a bushing, it
can be nested. Remember, the hole serves as a method to mount and an
alignment guide.

John Ferrell
My Competition is not my enemy!
http://DixieNC.US

----- Original Message -----
From: "Koenig, Tom" <Tom.Koenig at actewagl.com.au>
To: <discussion at nsrca.org>
Sent: Tuesday, November 16, 2004 7:36 PM
Subject: Further prop questions



Dave and others,

You wouldn't happen to know at what stage the centre holes are prepared
during the manufacturing process? I assume it's the last thing they do? For
the benefit of those unaware, an APC pattern size prop retails somewhere
around the $35 to $45 Australian. This has a few of us a little upset to say
the least....but that's another story.

Once again I purchased two new props. Burnt another$80. I attempted to
balance them, but could not. The holes in both props were again NOWHERE
close to the actual centre. The error is visible without the need to
measure. I am presently considering filling the holes with an epoxy/milled
glass mix, re-jigging and drilling the holes properly on centre. Does this
sound feasible?

 I in no way want to slam APC as I believe the APC prop is the only prop of
choice for our applications, but my collection of paint stirrers is getting
ridiculous. I cant imagine that we would be a dumping ground for out of spec
props. My drawer is literally full of thousands of dollars of props I have
collected over the last 15 years ( most are Ok) but it seems that the last
few years I seem to be getting these paint stirrers. Why this is so, I have
no idea. I am also not alone on this issue down here.

Lately, a group of us have been doing a 'bulk' order through Central. The
percentage of paint stirrers is (much) lower that way and not to mention the
cost saving is considerable...but sometimes when you need a prop urgently we
have no choice but to purchase at the much inflated (obscene!) local prices.

I wonder if APC would be willing to offer a 'blue printed and balanced'
version of their props? It would save me a fortune in money ( not to mention
time!) even if it cost a few dollars more per prop.

My apologies if I sound like I'm having a whinge, but I just hate being over
a barrel on things.

best regards

Tom


-----Original Message-----
From: discussion-request at nsrca.org
[mailto:discussion-request at nsrca.org]On Behalf Of David Lockhart
Sent: Tuesday, 16 November 2004 2:38 PM
To: discussion at nsrca.org
Subject: Re: 3-bladed props for OS160FX


Bill,

I think quite slim.

I've known Fred Burgdorf at APC since he started making props.  I'm not
privvy to exact production costs or sales volumes, but the production costs
for the molds on a 3 blader are much higher than an equivalent load 2 blade.
And I believe the sales volume of the pattern sized 3 and 4 blade props is
probably below or maybe at investment cost.  I'd guess the average 3 or 4
blade pattern APC prop has sold on the order of 200 copies - while props
like the 17-12 and 16.5-12W have sold on the order of thousands - that does
not lend to a money making scenario for any additional 3/4 blade pattern
props.  I know Fred would rather "mimic" a given 3 blade with a super wide
blade 2 blade prop (because of production costs) than make another 3 blade
prop.  I believe all of the APC molds are CNC milled solid aluminum blocks -
you can imagine how much larger the mold for a 3 blade is compared to a 2
blade, and aside from the simple size difference, I believe maintaining the
integrity of the mold and the injection process becomes more difficult as
well (I'd guess someone on this list might have more insight than this
Environmental Consultant).

If enough requests to apcprop.com were made, maybe another prop would make
it to production - I'd be happy to provide the prop for the mold <G>.

Regards,

Dave

----- Original Message -----
From: "William C. Harden" <flyinbill1 at bellsouth.net>
To: <discussion at nsrca.org>
Sent: Monday, November 15, 2004 8:18 PM
Subject: RE: 3-bladed props for OS160FX


> Dave,
>
> What is the possibility that we can get APC to make the 3-blade prop
> that we want??  It seems it would be in their best interest to do so.
>
> Bill Harden
>
> -----Original Message-----
> From: discussion-request at nsrca.org [mailto:discussion-request at nsrca.org]
> On Behalf Of David Lockhart
> Sent: Monday, November 15, 2004 6:55 PM
> To: discussion at nsrca.org
> Subject: Re: 3-bladed props for OS160FX
>
> Claudio,
>
> Below I've posted some info I've written before - I think most of it has
> been on this discussion list before.  In short, progressive twisting is
> not
> needed - a single twist near the root is sufficient.
>
> ions.
>
> =================================================
> To access the email archives for this list, go to
> http://lists.f3a.us/pipermail/nsrca-discussion/
> To be removed from this list, go to http://www.nsrca.org/discussionA.htm
> and follow the instructions.
>

=================================================
To access the email archives for this list, go to
http://lists.f3a.us/pipermail/nsrca-discussion/
To be removed from this list, go to http://www.nsrca.org/discussionA.htm
and follow the instructions.



************************************************************************
*PLEASE NOTE*  This email and any attachments may
be confidential. If received in error, please delete all
copies and advise the sender. The reproduction or
dissemination of this email or its attachments is
prohibited without the consent of the sender.

WARNING RE VIRUSES:  Our computer systems sweep
outgoing email to guard against viruses, but no warranty
is given that this email or its attachments are virus free.
Before opening or using attachments, please check for
viruses.  Our liability is limited to the re-supply of any
affected attachments.

Any views expressed in this message are those of the
individual sender, except where the sender expressly,
and with authority, states them to be the views of the
organisation.
************************************************************************
================To access the email archives for this list, go to
http://lists.f3a.us/pipermail/nsrca-discussion/
To be removed from this list, go to http://www.nsrca.org/discussionA.htm
and follow the instructions.


=================================================
To access the email archives for this list, go to
http://lists.f3a.us/pipermail/nsrca-discussion/
To be removed from this list, go to http://www.nsrca.org/discussionA.htm
and follow the instructions.

To access the email archives for this list, go to
http://lists.f3a.us/pipermail/nsrca-discussion/
To be removed from this list, go to http://www.nsrca.org/discussionA.htm
and follow the instructions.



=================================================
To access the email archives for this list, go to
http://lists.f3a.us/pipermail/nsrca-discussion/
To be removed from this list, go to http://www.nsrca.org/discussionA.htm
and follow the instructions.




More information about the NSRCA-discussion mailing list