A "Lockhart Prop" Update...

Wed May 26 02:28:26 AKDT 2004

Cox has been a wreck.  I just got this rpm message NOW (5:30 am,
Weds)....Dean, Vicente, my OS 1.60 on 15% with the Mac's 1290 at 19.75
turned Lockharts 15.75 x 12 three blade at 8160.  A different flavor of 15%
ran 7920.

Way too much.   I've ordered the 13 pitch and will try it.

Bob Pastorello
rcaerobob at cox.net
www.rcaerobats.net

----- Original Message ----- 
From: <vicenterc at comcast.net>
To: <discussion at nsrca.org>
Cc: "Dean Pappas" <d.pappas at kodeos.com>; <discussion at nsrca.org>
Sent: Tuesday, May 25, 2004 11:11 AM
Subject: RE: A "Lockhart Prop" Update...

> Just for your information.  Both the Mintor 140 and the OS 140 RX are
turning the 15.75x11 at around 7700 and 7600 respectively.  The Mintor is a
little stronger but the difference is not noticeable.  One time an sport
pilot approach me and asked me if my plane was ELECTRIC.
>
> Vicente
>
>
> > Go for it! Please remind me what are the particulars of your setup? i.e.
> > pump,pipe etc.
> > Dean
> >
> > -----Original Message-----
> > From: Bob Pastorello [mailto:emc2300 at yahoo.com]
> > Sent: Tuesday, May 25, 2004 10:50 AM
> > To: discussion at nsrca.org
> > Subject: RE: A "Lockhart Prop" Update...
> >
> >
> > Dean, I have NO doubt it will turn the 13.  My 12 was turning 8160 on
> > 15%, and it wasn't screaming lean.  Pipe was actually long-ish at
> > 19.75.  I plan on doing a 13 just to see....
> >
> > Bob.
> >
> > --- Dean Pappas <d.pappas at kodeos.com> wrote:
> > > Sounds good Bob,
> > > Actually the full 13-inch pitch offered great braking on a 140 RX
> > > with long pipe, but the engine/pipe/and needle all had to be spot-on
> > > to get the desired performance. That's when Dave started de-pitching
> > > the prop. I'm curious as to what RPM your 160 turns the 12" pitch
> > > prop, and as to whether the 160 will turn the stock 13" with
> > > authority. That will be super quiet.
> > > Dean
> > >
> > > -----Original Message-----
> > > From: Bob Pastorello [mailto:emc2300 at yahoo.com]
> > > Sent: Tuesday, May 25, 2004 9:56 AM
> > > To: discussion at nsrca.org
> > > Subject: Re: A "Lockhart Prop" Update...
> > >
> > >
> > > My error, Dave corrected me - it IS a 15.75 x 12.  And turns quite
> > > well
> > > on the 160.  Love it.
> > >
> > > Bob.
> > > --- vicenterc at comcast.net wrote:
> > > > Bob:
> > > >
> > > > I also using the "Lockhart Prop" on my Hydeout with same good
> > > > results.  I started to fly Masters this year and I was looking to
> > > > reduce the down lines the speed of the Hydeout.  I also was looking
> > > > for a hot and humid day and the engine (OS 140 RX) was able turn
> > > the
> > > > prop very well, and I didn't have problems.
> > > >
> > > > I flew my Focus and tried the prop.  I really liked the "constan
> > > > speed" effect on the Focus also.  The one I am using is 15.75x11
> > > > (original 15.75x13).  Probably you have the Mintor 1.7 or OS 160
> > > > since you are using 15.5x12.  It is 15.75 or 15.5?  I think I have
> > > > 15.75.
> > > >
> > > > Vicente Bortone
> > > >
> > > >
> > > >
> > > >
> > > >
> > >
> > > > ATTACHMENT part 2 message/rfc822
> > > > From:    "Bob Pastorello" <rcaerobob at cox.net>
> > > > To:    "NSRCA" <discussion at nsrca.org>
> > > > Subject:    A "Lockhart Prop" Update...
> > > > Date:    Tue, 25 May 2004 02:10:40 +0000
> > > >
> > > > This past weekend, I enjoyed the challenge (ahem) of attempting to
> > > > fly in the most incredible turbulence, gusts, and changes in
> > > > direction of wind during a pattern contest that I can recall.  The
> > > > first thing I made note of on practice day was that the APC 17 x 12
> > > > Std was WAY too fast on the Arresti (11 lbs), so I had to try the
> > > > Lockhart Twister....bolted on at the motel on Friday night...
> > > >     Saturday - early enough to rudely awaken all the sloths in the
> > > > motor home (Team A/S, you there??), I managed a quick test flight.
> > > I
> > > > was happily surprised to clearly see what I was after.  Good
> > > > acceleration - not nearly as rapid on the bite as a 2 blade Std,
> > > but
> > > > plenty good - and really exceptional braking.  The three blader
> > > just
> > > > offerred this very smooth dynamic brake that really made it easier
> > > to
> > > > manage things.
> > > >     My thanks to Dave Lockhart for doing his re-pitch, and my plea
> > > to
> > > > Fred Burgdorf to make a mold.  The 15.5 x 12 three blade is a
> > > > wonderful setup...mine was turning about 8150 on Magnum 15%,
> > > slightly
> > > > less on two other brands I was able to run side by side.  I was
> > > very
> > > > surprised to actually see 120 rpm difference on a prop of this
> > > load.
> > > >     Anywho - if you guys are looking for a great braking prop that
> > > > still operates in the torque band of our motors - contact Dave
> > > > Lockhart....(Lance - I'm sure he can replace your modified
> > > > prop...<G>)
> > > >
> > > > Bob Pastorello
> > > > rcaerobob at cox.net
> > > > www.rcaerobats.net
> > > >
> > > >
> > >
> > >
> > > =====
> > > Bob Pastorello
> > > rcaerobob at cox.net
> > > emc2300 at yahoo.com
> > >
> > >
> > >
> > >
> > > __________________________________
> > > Do you Yahoo!?
> > > Friends.  Fun.  Try the all-new Yahoo! Messenger.
> > > http://messenger.yahoo.com/
> > > =====================================
> > > # To be removed from this list, go to
> > > http://www.nsrca.org/discussionA.htm
> > > and follow the instructions.
> > >
> > > ====================================# To be removed from this list,
> > > go to http://www.nsrca.org/discussionA.htm
> > > and follow the instructions.
> > >
> >
> >
> > =====
> > Bob Pastorello
> > rcaerobob at cox.net
> > emc2300 at yahoo.com
> >
> >
> >
> >
> > __________________________________
> > Do you Yahoo!?
> > Friends.  Fun.  Try the all-new Yahoo! Messenger.
> > http://messenger.yahoo.com/
> > =====================================
> > # To be removed from this list, go to
http://www.nsrca.org/discussionA.htm
> > and follow the instructions.
> >
> > # To be removed from this list, go to
> > http://www.nsrca.org/discussionA.htm
> > and follow the instructions.
> >
> =====================================
> # To be removed from this list, go to http://www.nsrca.org/discussionA.htm
> and follow the instructions.
>

=====================================
# To be removed from this list, go to http://www.nsrca.org/discussionA.htm
and follow the instructions.