power

[Tom Hinton]

It is a JR and trans is Futaba but its on the same channel. It should still
work shouldn't it?

----- Original Message -----
From: <jivey61 at bellsouth.net>
To: <discussion at nsrca.org>
Sent: Thursday, June 24, 2004 9:35 PM
Subject: Re: Re: power


> Tom
> Either the receiver is on a different channel or it is bad,if your set up
worked with a different receiver. You said you purchased a new receiver.Also
is it the same type(compatible) with the transmitter. Is it JR,Futaba,etc.
>
> Jim  Ivey
>
> >
> > From: "Tom Hinton" <tph1 at bellsouth.net>
> > Date: 2004/06/24 Thu PM 08:21:37 EDT
> > To: <discussion at nsrca.org>
> > Subject: Re: Re: power
> >
> > It's brand new also. But I guess it could be bad.
> >
> > ----- Original Message -----
> > From: "Joe Dunnaway" <dunnaway at geopath.com>
> > To: <discussion at nsrca.org>
> > Sent: Thursday, June 24, 2004 8:12 PM
> > Subject: Re: Re: power
> >
> >
> > > Check your crystal... It may be bad.
> > > Try replacing it with another crystal from a receiver that works.
> > >
> > > Joe Dunnaway
> > >
> > > ----- Original Message -----
> > > From: "Tom Hinton" <tph1 at bellsouth.net>
> > > To: <discussion at nsrca.org>
> > > Sent: Thursday, June 24, 2004 7:07 PM
> > > Subject: Re: Re: power
> > >
> > >
> > > > I have 5.71/5.72 volts at the pins on every channel. Any I deas now?
> > > > thanks, Tom
> > > > ----- Original Message -----
> > > > From: "Tom Hinton" <tph1 at bellsouth.net>
> > > > To: <discussion at nsrca.org>
> > > > Sent: Thursday, June 24, 2004 7:55 PM
> > > > Subject: Re: Re: power
> > > >
> > > >
> > > > > Where do I check it at the receiver? I have a good meter.
> > > > > thanks
> > > > > ----- Original Message -----
> > > > > From: <jivey61 at bellsouth.net>
> > > > > To: <discussion at nsrca.org>
> > > > > Sent: Thursday, June 24, 2004 7:54 PM
> > > > > Subject: Re: Re: power
> > > > >
> > > > >
> > > > > >
> > > > > > > Tom
> > > > > >  You must have a bad switch or broken wire. If you have a
voltmeter
> > > see
> > > > if
> > > > > you have 4.8 volts at the receiver.When the servos won't jog a bit
> > when
> > > > you
> > > > > turn switch on-off,something is not getting through.
> > > > > > Jim Ivey
> > > > > >
> > > > > > Jim Ivey
> > > > > > > From: "Tom Hinton" <tph1 at bellsouth.net>
> > > > > > > Date: 2004/06/24 Thu PM 07:48:29 EDT
> > > > > > > To: <discussion at nsrca.org>
> > > > > > > Subject: Re: power
> > > > > > >
> > > > > > > Yeah Mike I checked that. It's a FM receiver and the trans is
on
> > > PPM.
> > > > > > >   ----- Original Message -----
> > > > > > >   From: Mike Hester
> > > > > > >   To: discussion at nsrca.org
> > > > > > >   Sent: Thursday, June 24, 2004 7:43 PM
> > > > > > >   Subject: Re: power
> > > > > > >
> > > > > > >
> > > > > > >   Are you sure the transmitter is set to the correct
modulation
> > for
> > > > the
> > > > > reciever? Stupid thought, but one time I pulled my hair out for
hours
> > > > until
> > > > > I realized that the transmitter was set to PPM and it was a PCM
> > > reciever.
> > > > > Now it's the first thing I check. Just a thought.
> > > > > > >
> > > > > > >   -Mike
> > > > > > >     ----- Original Message -----
> > > > > > >     From: Tom Hinton
> > > > > > >     To: discussion at nsrca.org
> > > > > > >     Sent: Thursday, June 24, 2004 7:32 PM
> > > > > > >     Subject: power
> > > > > > >
> > > > > > >
> > > > > > >     I just bought another receiver and tried to install it in
my
> > > > Desire.
> > > > > Nothing, I mean nothing works. The battery is charged, over 5
volts,
> > > > switch
> > > > > is plugged in right, same freq. as trans..  Not even any movement
when
> > > > first
> > > > > turned on after moving an arm when off. Any ideas?
> > > > > > >     thanks
> > > > > > >
> > > > > >
> > > > > > =====================================
> > > > > > # To be removed from this list, go to
> > > > http://www.nsrca.org/discussionA.htm
> > > > > > and follow the instructions.
> > > > > >
> > > > >
> > > > > =====================================
> > > > > # To be removed from this list, go to
> > > http://www.nsrca.org/discussionA.htm
> > > > > and follow the instructions.
> > > > >
> > > >
> > > > =====================================
> > > > # To be removed from this list, go to
> > http://www.nsrca.org/discussionA.htm
> > > > and follow the instructions.
> > >
> > > =====================================
> > > # To be removed from this list, go to
http://www.nsrca.org/discussionA.htm
> > > and follow the instructions.
> > >
> > >
> >
> > =====================================
> > # To be removed from this list, go to
http://www.nsrca.org/discussionA.htm
> > and follow the instructions.
> >
> >
>
> =====================================
> # To be removed from this list, go to http://www.nsrca.org/discussionA.htm
> and follow the instructions.
>

=====================================
# To be removed from this list, go to http://www.nsrca.org/discussionA.htm
and follow the instructions.