power

[Joe Dunnaway]

Check your crystal... It may be bad.
Try replacing it with another crystal from a receiver that works.

Joe Dunnaway

----- Original Message ----- 
From: "Tom Hinton" <tph1 at bellsouth.net>
To: <discussion at nsrca.org>
Sent: Thursday, June 24, 2004 7:07 PM
Subject: Re: Re: power


> I have 5.71/5.72 volts at the pins on every channel. Any I deas now?
> thanks, Tom
> ----- Original Message -----
> From: "Tom Hinton" <tph1 at bellsouth.net>
> To: <discussion at nsrca.org>
> Sent: Thursday, June 24, 2004 7:55 PM
> Subject: Re: Re: power
>
>
> > Where do I check it at the receiver? I have a good meter.
> > thanks
> > ----- Original Message -----
> > From: <jivey61 at bellsouth.net>
> > To: <discussion at nsrca.org>
> > Sent: Thursday, June 24, 2004 7:54 PM
> > Subject: Re: Re: power
> >
> >
> > >
> > > > Tom
> > >  You must have a bad switch or broken wire. If you have a voltmeter
see
> if
> > you have 4.8 volts at the receiver.When the servos won't jog a bit when
> you
> > turn switch on-off,something is not getting through.
> > > Jim Ivey
> > >
> > > Jim Ivey
> > > > From: "Tom Hinton" <tph1 at bellsouth.net>
> > > > Date: 2004/06/24 Thu PM 07:48:29 EDT
> > > > To: <discussion at nsrca.org>
> > > > Subject: Re: power
> > > >
> > > > Yeah Mike I checked that. It's a FM receiver and the trans is on
PPM.
> > > >   ----- Original Message -----
> > > >   From: Mike Hester
> > > >   To: discussion at nsrca.org
> > > >   Sent: Thursday, June 24, 2004 7:43 PM
> > > >   Subject: Re: power
> > > >
> > > >
> > > >   Are you sure the transmitter is set to the correct modulation for
> the
> > reciever? Stupid thought, but one time I pulled my hair out for hours
> until
> > I realized that the transmitter was set to PPM and it was a PCM
reciever.
> > Now it's the first thing I check. Just a thought.
> > > >
> > > >   -Mike
> > > >     ----- Original Message -----
> > > >     From: Tom Hinton
> > > >     To: discussion at nsrca.org
> > > >     Sent: Thursday, June 24, 2004 7:32 PM
> > > >     Subject: power
> > > >
> > > >
> > > >     I just bought another receiver and tried to install it in my
> Desire.
> > Nothing, I mean nothing works. The battery is charged, over 5 volts,
> switch
> > is plugged in right, same freq. as trans..  Not even any movement when
> first
> > turned on after moving an arm when off. Any ideas?
> > > >     thanks
> > > >
> > >
> > > =====================================
> > > # To be removed from this list, go to
> http://www.nsrca.org/discussionA.htm
> > > and follow the instructions.
> > >
> >
> > =====================================
> > # To be removed from this list, go to
http://www.nsrca.org/discussionA.htm
> > and follow the instructions.
> >
>
> =====================================
> # To be removed from this list, go to http://www.nsrca.org/discussionA.htm
> and follow the instructions.

=====================================
# To be removed from this list, go to http://www.nsrca.org/discussionA.htm
and follow the instructions.