PPG basecoat clear coat question

[Brian Young]

...lol

..

--- Keith Hoard <khoard at midsouth.rr.com> wrote:
> Dang it Ron. . . you beat me to it!!!
> 
> 
> Keith L. Hoard
> Cordova, TN
> khoard at midsouth.rr.com
> 
> 
> ----- Original Message ----- 
> From: "Ron Van Putte" <vanputte at cox.net>
> To: <discussion at nsrca.org>
> Sent: Tuesday, February 24, 2004 5:06 PM
> Subject: Re: PPG basecoat clear coat question
> 
> 
> > 
> > On Feb 24, 2004, at 4:33 PM, Brian Young wrote:
> > 
> > > Buddy, how long does it take to rub out a plane?
> > 
> > Sorry - I can't resist.  If you fail to hook up
> the aileron servos, it 
> > doesn't take long at all. <BG>
> > 
> > Ron Van Putte
> > 
> > >
> > > --- BUDDYonRC at aol.com wrote:
> > >>  Troy is correct except I opt for no clear
> coat.
> > >> After I paint the base color I wait overnight
> then
> > >> wet sand the entire
> > >> airplane with 2000 grit sandpaper after it is
> sanded
> > >> to where the entire surface has
> > >> the same dull appearance and being careful not
> to
> > >> sand through I mask and
> > >> paint the trim colors. Wait overnight, remove
> the
> > >> mask and sand the trim colors
> > >> to remove all sharp edges along mask lines.
> > >> After all is sanded I polish out with 3-M
> Imperial
> > >> Hand Glaze #39007
> > >> I don't see a good reason to clear coat this
> system,
> > >> after it cures for a few
> > >> days acetone wont even phase it.
> > >> It is important that if you use a primer use
> PPG
> > >> K-36 or equal some primers
> > >> are not fuel proof and hot fuel can damage the
> > >> finish if it gets under the
> > >> painted surface in places where you drill holes
> to
> > >> install engine needle valve
> > >> access or other equipment.
> > >> Sanding before you add trim colors removes
> weight.
> > >> dust, bugs or anything
> > >> else that fell on the wet paint and also allows
> you
> > >> to sand out any runs in the
> > >> paint if you end up with any it also assures a
> > >> smooth mask surface which will
> > >> minimize run under of the trim colors
> > >> Buddy Brammer
> > >>
> > >
> > >
> > > __________________________________
> > > Do you Yahoo!?
> > > Yahoo! Mail SpamGuard - Read only the mail you
> want.
> > > http://antispam.yahoo.com/tools
> > > =====================================
> > > # To be removed from this list, send a message
> to
> > > # discussion-request at nsrca.org
> > > # and put leave discussion on the first line of
> the body.
> > > #
> > >
> > 
> > =====================================
> > # To be removed from this list, send a message to 
> > # discussion-request at nsrca.org
> > # and put leave discussion on the first line of
> the body.
> > #
> > 
> 
> =====================================
> # To be removed from this list, send a message to 
> # discussion-request at nsrca.org
> # and put leave discussion on the first line of the
> body.
> #
> 


__________________________________
Do you Yahoo!?
Yahoo! Mail SpamGuard - Read only the mail you want.
http://antispam.yahoo.com/tools
=====================================
# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#