OS 91FX

[Ihncheol Park]

Tower hobbies has them for $4.79
Your local hobbyshops should be able to get you a good price also.
Gasket set. OS part # 29514000 or Tower Part# LXCM87

Ihncheol
-----Original Message-----
From: discussion-request at nsrca.org
[mailto:discussion-request at nsrca.org]On Behalf Of randy10926 at comcast.net
Sent: Monday, October 27, 2003 8:49 AM
To: discussion at nsrca.org
Subject: RE: OS 91FX


Been thinking of putting my OS91FX into the Killer Chaos I am building.
Added a turtle deck to the Fuse that goes to the middle of the wing.
Probably don't need it but I have a header and pipe for the engine as well.

My OS91FX runs better with a Perry carb up front; but have not needed the
pump yet.  May turn adding a head shim.   Where do you get them?

Randy
> Nat,
>
> What are the differences between running the 17x10N cut down to 16" and
> normal 16x10?
> Also, from a pro_performance spreadsheet which I downloaded from a
website.
> Thrust = 2.83E-12 x RPM^2 x D^4
>
> 15x8 @ 10K rpm (actually running rpm): 15.9 pound of thrust show up.
> 17x10 @7800 : 15.96 pound
> 16x10 @8000 : 13.18 pound
>
> Not really sure if the equation is meaningful at the actual running.
> Are you using the larger diameter prop to reduce noise?
> I also heard you were using 91SX-H.
>
> Ihncheol Park
>
> -----Original Message-----
> From: discussion-request at nsrca.org
> [mailto:discussion-request at nsrca.org]On Behalf Of Nat Penton
> Sent: Saturday, October 25, 2003 10:25 PM
> To: discussion at nsrca.org
> Subject: Re: OS 91FX
>
>
> Matt I will add additional  info. Have been running the 91FX over two
years
> and it will carry my 8+ lb airplanes to the moon. On fuel - was using
> Ritches 20%, now 30%,idles under 1500. Pipe length- 26 to 28" depending on
> which pipe, most power from ES 2 stk(1 9/16 OD), Favorite props 17X10N cut
> to16" and 15.5X12, rpms around 7700. Using Hanno (same as 140RX) backplate
> pump. Can be installed with simple tools and a little ingenuity. O yes 2
> headshims. Stock bearings good for about 30 flts, Boca sealed well over
100,
> leave all seals in place. Provide crankcase cooling for longer bearing
life.
> Have not tried 15CC Hatori or MACS but plan to. Headers are from Karl
> Mueller,very nice.
> ----- Original Message -----
> From: "David Gundling" <DGundling at compuserve.com>
> To: <discussion at nsrca.org>
> Sent: Saturday, October 25, 2003 8:34 AM
> Subject: Re: OS 91FX
>
>
> > Message text written by INTERNET:discussion at nsrca.org
> > >The 91 FX is stronger than the ys 91 4 cycle with some margin. Stretch
> the
> >
> > pipe a bit with an extra long header and run the larger prop. The set-up
> > will
> > amaze you with its output and quietness. Good friend Nat is using it on
> his
> >
> > X-Press turning a 17x10 N cut down 1/2 inch. Plenty of power for the 8-9
> > pound
> > plane.
> >
> > Matt K<
> >
> > Matt,
> >
> > Thanks.
> >
> > Dave
> > # To be removed from this list, send a message to
> > # discussion-request at nsrca.org
> > # and put leave discussion on the first line of the body.
> > #
> >
> >
> >
>
> =====================================
> # To be removed from this list, send a message to
> # discussion-request at nsrca.org
> # and put leave discussion on the first line of the body.
> #
>
>
> =====================================
> # To be removed from this list, send a message to
> # discussion-request at nsrca.org
> # and put leave discussion on the first line of the body.
> #
>
=====================================
# To be removed from this list, send a message to
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#



=====================================
# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#