Modelltechnik Rhapsody

Dean Pappas d.pappas at kodeos.com
Thu May 22 12:30:34 AKDT 2003


You wouldn't ... that's the point.
Thanks for the clarifying question.
Dean

-----Original Message-----
From: Ron Van Putte [mailto:vanputte at nuc.net]
Sent: Thursday, May 22, 2003 4:27 PM
To: discussion at nsrca.org
Subject: Re: Modelltechnik Rhapsody




Dean Pappas wrote:

>Compadre,
>It is very easy to get the midrange so lean that the engine starves there.
>The idle mixture controls the mid-range, and the main needle is less effective there.
>Short pipe length richens the middle as well.
>Do yourself a favor, after setting the top end, put the engine at mid throttle and pinch the fuel line to see if you are too lean.
>Don't be surprised if its too lean to hear the Rs pick up.
>  
>

What am I missing?  If it's too lean, why would RPMs pick up when you 
pinch the fuel line?

Ron Van Putte

>
>-----Original Message-----
>From: Jason [mailto:jshulman at theriver.com]
>Sent: Thursday, May 22, 2003 4:05 PM
>To: discussion at nsrca.org
>Subject: RE: Modelltechnik Rhapsody
>
>
>I'm running two OS-F's, so it sputters from low to high power. I've been
>told to get some A5's in there to take care of the problem, so I ordered
>some finally. I'll report over the weekend.
>
>Jason
>
>-----Original Message-----
>From: discussion-request at nsrca.org
>[mailto:discussion-request at nsrca.org]On Behalf Of Dean Pappas
>Sent: Thursday, May 22, 2003 1:02 PM
>To: discussion at nsrca.org
>Subject: RE: Modelltechnik Rhapsody
>
>
>Transition?
>What does it do ... more to the point, mine has utterly impeccable table
>manners!
>I'm curious if there's a problem.
>Dean
>
>-----Original Message-----
>From: Jason [mailto:jshulman at theriver.com]
>Sent: Thursday, May 22, 2003 3:47 PM
>To: discussion at nsrca.org
>Subject: RE: Modelltechnik Rhapsody
>
>
>So far, so good. Going to cut the header a bit and stick the ES pipe back
>on. Transition should improve tomorrow when I get some A5 plugs. Got to love
>the power, especially in my heavy planes.
>
>Jason
>
>-----Original Message-----
>From: discussion-request at nsrca.org
>[mailto:discussion-request at nsrca.org]On Behalf Of Dean Pappas
>Sent: Thursday, May 22, 2003 12:42 PM
>To: discussion at nsrca.org
>Subject: RE: Modelltechnik Rhapsody
>
>
>Hey Jason,
>How's you 170 running?
>Are you still running it?
>Dean
>
>-----Original Message-----
>From: Jason [mailto:jshulman at theriver.com]
>Sent: Thursday, May 22, 2003 3:24 PM
>To: NSRCA
>Subject: Modelltechnik Rhapsody
>
>
>Did someone post something about having one of these a little while ago? If
>so, can someone steer me to the site again.
>
>Thanks,
>Jason
>www.jasonshulman.com
>
>
>=====================================
># To be removed from this list, send a message to
># discussion-request at nsrca.org
># and put leave discussion on the first line of the body.
>#
>
>============# To be removed from this list, send a message to
># discussion-request at nsrca.org
># and put leave discussion on the first line of the body.
>#
>
>
>=====================================
># To be removed from this list, send a message to
># discussion-request at nsrca.org
># and put leave discussion on the first line of the body.
>#
>
>============# To be removed from this list, send a message to
># discussion-request at nsrca.org
># and put leave discussion on the first line of the body.
>#
>
>
>
>=====================================
># To be removed from this list, send a message to 
># discussion-request at nsrca.org
># and put leave discussion on the first line of the body.
>#
>
># To be removed from this list, send a message to 
># discussion-request at nsrca.org
># and put leave discussion on the first line of the body.
>#
>
>
>  
>


=====================================
# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#

==================# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#



More information about the NSRCA-discussion mailing list