New Mintors

[patterndude at attbi.com]

Oh, I also have only used A5 plugs.  I'm curious to see your comparisons when 
you start using them.
--Lance
> Lance,
>        I much prefer to have a tight engine. (Most engines that we receive are a 
> compromise so that the users don't break them). I would suggest that the 
> break-in instructions need to be a bit more comprehensive. The 170 may also be 
> different to the 1.40. (The Moki needed a similar break-in.) BTW it was not 
> cowled in very much. I had removed the top to accommodate the DZ pump. I then 
> removed most of the front to accommodate the carb. (The Hydeout is quite narrow 
> at the spinner.)
> 
> I tried using two different plugs on my modified OS 1.60 and one always died. I 
> will switch to the recommenced A5's when I get a cool run and see how they do.
> 
> The vertical was strong even though it was just a 16" prop. It was also nice and 
> quiet. Looking forward to trying some of my 3-blade props later on.
> 
> Eric.
>        
> 
> -----Original Message-----
> From: discussion-request at nsrca.org
> [mailto:discussion-request at nsrca.org]On Behalf Of patterndude at attbi.com
> Sent: Monday, May 12, 2003 1:11 AM
> To: discussion at nsrca.org
> Subject: Re: New Mintors
> 
> 
> Eric,
> I ran a gallon thru my two on the bench before putting them in the air.  There 
> have been several posts of people putting them up quickly and they've reported 
> success.  More power to them.  I'm sure there are different break-in 
> procedures that work.
>   In my case, similar to yours, the engines seemed tight at first.  I found 
> that they ran fine at mid throttle out of the box and the range extended with 
> a little running.  Your procedure sounds like it's working, but I agree it may 
> not be for everyone.
>   The way I've always looked at it, break-in is a temporary condition.  No 
> need to rush it.  I have a friend with a Saito 180 which took a while to break 
> in but then became a very reliable engine.  I'm not trying to associate one 
> engine with another, just pointing out that reliable engines result from a 
> variety of starting points. 
>   Thanks for sharing your experiences.  
> --Lance

> > Partially broke-in my Mintor in today with help from Dave Lockhart. Initially 
> > the engine was very tight and got hot very quickly. 
> >  
> > I switched to two F plugs and used sport 2-c 15% with 18% oil. Still tight and 
> > hard to keep running without overheating. Finally I got a run with a high idle 
> > that did not overheat. Then Dave persuaded me to go to full throttle and set 
> it 
> > rich. It worked much better this time. A tank later we put it in the air. It 
> ran 
> > very rich in the air. Several landings later ... with Dave turning in the 
> needle 
> > a click or two at a time.. we got a flight where we could lean it by climbing 
> > and cool  down by diving. Round and square loops did the job. Another run on 
> the 
> > ground and a slightly leaner run in the air and it was almost running like a 
> > 2-c.
> >  
> > The power on a 16 x 12 APC was encouraging and the idle began to be more 
> > reliable.. I know the engine was tight before I began but was surprised that I 
> > had to be so diligent with the break-in. My question to you experienced 
> > Mintor-men is. "Is this usual?" Not complaining, but without my own and 
> David's 
> > experience a "Rookie" could struggle...
> >  
> > Regards,
> >  
> > Eric.
> >  
> > 
> =====================================
> # To be removed from this list, send a message to 
> # discussion-request at nsrca.org
> # and put leave discussion on the first line of the body.
> #
> 
> # To be removed from this list, send a message to 
> # discussion-request at nsrca.org
> # and put leave discussion on the first line of the body.
> #
> 
=====================================
# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#