ST2300 conrod, wrist pin end

Del Rykert drykert at rochester.rr.com
Wed Jun 25 15:04:29 AKDT 2003


Try buying a few YS 120 ac parts if you can find them and without anything major run up to $150. No crank,piston,cylinder,sleeve,rod or pin. Just a couple of rocker arms, push rods, springs & e clips.
 
     Del K. Rykert
     AMA - 8928 
     NSRCA - 473
     Kb2joi - General 

 
  ----- Original Message ----- 
  From: jim ivey 
  To: discussion 
  Sent: Tuesday, June 24, 2003 3:51 PM
  Subject: Re: ST2300 conrod, wrist pin end


  Well,  A Webra rod is only $24.95.

  Jim Ivey

    ----- Original Message -----
    From: ronlock
    Sent: Tuesday, June 24, 2003 6:46 PM
    To: discussion at nsrca.org
    Subject: Re: ST2300 conrod, wrist pin end

    Ed,  Maybe an OS 140RX rod would fit, they are "only"  $34.99.  <G>
    Ron Lockhart
      ----- Original Message ----- 
      From: Ed Miller 
      To: discussion at nsrca.org 
      Sent: Monday, June 23, 2003 11:37 PM
      Subject: Re: ST2300 conrod, wrist pin end


      Oh sure, Tower will gladly sell me a new conrod for the bargain price of $39.99. That's even a bigger theft than YS parts : )
      Ed M.
        ----- Original Message ----- 
        From: Emory Schroeter 
        To: edbon85 at optonline.net 
        Sent: Monday, June 23, 2003 10:56 PM
        Subject: Re: ST2300 conrod, wrist pin end


        Nope. I haven't had that problem. Can you get a replacement part?

        Emory Schroeter
          ----- Original Message ----- 
          From: Ed Miller 
          To: discussion at nsrca.org 
          Sent: Monday, June 23, 2003 10:41 PM
          Subject: ST2300 conrod, wrist pin end


          Any of you folks out there that have been running ST2300's ever experience a short lived wrist pin end of the con rod ?? I have approximately 100 flights on a ST2300 in a Hanson Dalotel spinning an APC 18x8 with S&W fuels 20% to 30% nitro ( 20% oil in all fuels ) and the bushing in the wrist pin end of the con rod is worn out. I'd say there is at least .030" clearance, maybe more. Engine was down about 700rpm on the ground and never really settled on a rpm and acted lean in the air, in verticals it went flat, would no longer haul plane vertically indefinately. This all happened in maybe 5 or 6 flights, went from a powerhouse to a dog. There is only one small hole in the top of the conrod to lube the wrist pin ( approx .040" in dia. ), the wrist pin is fine and measures no wear at all where the conrod rides on it. I'm going to order a new conrod, if the new one only has one hole in it I may enlarge it a bit as well as add a second hole from the bottom of the wrist pin boss on the rod. Luckily I have a 2nd ST2300, just installed it and I'm back to 8800 rpm on 25% nitro with the 18x8 so I'm ready for the Pocono pattern contest. Both my ST2300's are Italian made, the only notable difference is one has a longer crankshaft ( prop end ).
          Thanks...Ed M.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.f3a.us/pipermail/nsrca-discussion/attachments/20030625/94d8f6ad/attachment.html


More information about the NSRCA-discussion mailing list