Radical thinking...

[Atwood, Mark]

Talk about a sled!  36" at 10lbs????  Please tell me you meant 72".

I like the K4 on landing though...including FAI.  We're getting lazy :)

-Mark


-----Original Message-----
From:	John Ferrell [mailto:johnferrell at earthlink.net]
Sent:	Sat 7/5/2003 2:02 PM
To:	discussion at nsrca.org
Cc:	
Subject:	Radical thinking...

Too much of the tail wagging the dog here!
Lets get a little radical on the rules here:
Not 2 meters, but 36 INCHES.
Not 11 pounds, but 10 pounds.
While we are at it, let's make landings K4. 
A 5% bonus for airplane under 94db at 10 Feet.

John Ferrell 
6241 Phillippi Rd
Julian NC 27283
Phone: (336)685-9606  
johnferrell at earthlink.net
Dixie Competition Products
NSRCA 479 AMA 4190  W8CCW
"My Competition is Not My Enemy"

  ----- Original Message ----- 
  From: Del Rykert 
  To: discussion at nsrca.org 
  Sent: Saturday, July 05, 2003 1:58 PM
  Subject: Re: OS Piston Pin


  Raising weight limit also has potential of being FAI issue which AMA has followed their lead in regard to Precision Aerobatics. The U.S. is only 1 vote and many other countries would have to agree. To have AMA be different from FAI has in the past shown not to be the best situation.

       Del K. Rykert
       AMA - 8928 
       NSRCA - 473
       Kb2joi - General 


    ----- Original Message ----- 
    From: VicenteRC at aol.com 
    To: discussion at nsrca.org 
    Sent: Saturday, July 05, 2003 6:03 AM
    Subject: Re: OS Piston Pin


    Jim:

    The problem with gasoline engines is that in the range size and power of the OS 140 or similar, the gasoline engine weight between 1 lb and 1.5 lb more.  It will be nice that the manufacturers go back to drawing board and produce a very light gasoline that could be used pattern.

    Regards,

    Vicente Bortone





    In a message dated 7/4/2003 1:00:53 PM Eastern Standard Time, JOddino at socal.rr.com writes:

    > 
    > 
    > You folks are sure making a case for gas engines with enough displacement to
    > get the job done.  My DA50 is barely broken in at 100 flights.  I recently
    > got an e-mail from a guy who put one in a Gator Giles 202.  It went to 14
    > pounds but I bet it does exactly what pattern pilots are looking for.  Super
    > thrust and good braking.  Get rid of the weight limit and you'd see whole
    > new breed of two meter pattern planes.
    > My 202 with the OS 1.40 EFI is sitting collecting dust since the bearing
    > went out at, you got it, 100 flights.  I'd rather fly than rebuild engines.
    > Jim
    > ----- Original Message ----- 
    > From: <flyboy422 at juno.com>
    > To: <discussion at nsrca.org>
    > Sent: Friday, July 04, 2003 9:09 AM
    > Subject: Re: OS Piston Pin
    > 
    > 
    > > Verne,
    > >
    > >      If you can stand one more take on the OS piston I'll share my
    > > experience.  I have been flying OS 140's for 3 years which means I have
    > > been changing bearings at least twice a year.  Everything that has been
    > > written on the list regarding the wrist pin is correct.  The method I use
    > > for the bearing is as follows:  Perheat your oven to 500 degrees.  Clean
    > > as much fuel off the case as you can.  Put the case in the oven for 30
    > > minutes.  When you open the oven door, the bearing will be out of the
    > > case.  If  you are not this lucky, it will only take a slight rap to
    > > finish the job.  Put the new bearing(stainless) in the freezer for the
    > > same 30 minutes.  I remove any shields from the bearing.  They only will
    > > restrict lubrication.  Put the bearing onto the crankshaft and insert
    > > into the case.  I know you'll know what to do next.
    > >
    > >        I suggest you use only stainless bearings and expect to get about
    > > 100 runs out of it.  The early warning sign of wear will be a slight
    > > rocking of the prop when the engine is hot.    Once that starts you have
    > > about 10 flights left.  I use after run oil religiously.  
    > Good luck and
    > > I'll see you at the Nats.
    > >
    > > Steve Miller
    > > =====================================
    > > # To be removed from this list, send a message to
    > > # discussion-request at nsrca.org
    > > # and put leave discussion on the first line of the body.
    > > #
    > >
    > 
    > =====================================
    > # To be removed from this list, send a message to 
    > # discussion-request at nsrca.org
    > # and put leave discussion on the first line of the body.
    > #
    =====================================
    # To be removed from this list, send a message to 
    # discussion-request at nsrca.org
    # and put leave discussion on the first line of the body.
    #



-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/ms-tnef
Size: 4768 bytes
Desc: not available
Url : http://lists.f3a.us/pipermail/nsrca-discussion/attachments/20030705/83ceb0e4/attachment.bin