Scoop-Making

[Bob Pastorello]

Thanks to all....I made a scoop out of a set of 40 size wheel pant ends....photos later!!!
Appreciate the help!

Bob Pastorello, Oklahoma
NSRCA 199, IMAC 1320, AMA 46373
rcaerobob at cox.net
www.rcaerobats.net


  ----- Original Message ----- 
  From: Henderson,Eric 
  To: discussion at nsrca.org 
  Sent: Wednesday, July 02, 2003 10:34 AM
  Subject: RE: Scoop-Making


  I made several out of wheel pants. The SIG ones came in two halves. I just cut of the rear sections to get two scoops.

  Eric.


  -----Original Message-----
  From: discussion-request at nsrca.org [mailto:discussion-request at nsrca.org]On Behalf Of John Ferrell
  Sent: Wednesday, July 02, 2003 11:28 AM
  To: discussion at nsrca.org
  Subject: Re: Scoop-Making


  If you would like to dabble a bit in a small glass project scoops are an ideal subject. Just about any epoxy will work well. Check out the spoons available in housewares (avoid the kitchen drawers unless you are batchelor or want to be one). You can make the mold using a carved up spoon, play dough, paper mache,wood scraps, balsa or whatver your imagination will provide.  I like to hold the stuff together with hot melt glue.Avoid polyester resin because it will probably get hot enough to melt your mold. If you don't happen to have any suitable glass fabric, scrap from the rag bag, or a handkerchief will do...these are not structural parts. Use some kind of wax for mold release, I like paste floor wax like I use on the table saw. Try to avoid a wax with silicon, it will be very hard to paint otherwise. After waxing, spray with with hair spray.

  If your model is not destroyed taking it out of the mold, you spent too much time on it!

  When you do the lay up, wax the mold at least 3 times, polishing each time. Spray liberally with hair spray. avoid runs, they will require filling in the part. When you start the lay up in the mold first paint it with a thin coat of the epoxy. That will assure a passible finish. It takes longer, but small scraps of cloth are easier to fit in place without wrinkles. try to make the fabric cuts at 45 degrees to the threads, it will conform to the curves easier. 

  You don't have much to lose with this size project!

  Fitting the scoops to the fuse:
  Tape sandpaper to the fuse (smooth side down).
  Rub part carefully against the location to be fitted. 
  John Ferrell 
  6241 Phillippi Rd
  Julian NC 27283
  Phone: (336)685-9606  
  johnferrell at earthlink.net
  Dixie Competition Products
  NSRCA 479 AMA 4190  W8CCW
  "My Competition is Not My Enemy"

    ----- Original Message ----- 
    From: Bob Pastorello 
    To: NSRCAMail 
    Sent: Wednesday, July 02, 2003 7:22 AM
    Subject: Scoop-Making


    Decided I want to use a scoop on my latest for crankcase/bearing cooling.  I know where to locate it on the cowl, but have no idea of shape, angle, if any "ducting" is needed.  It looks like the scoops out there just direct air based on their shape alone...without ducting.
        Anyone have any suggestions/ideas on this?
        What to make the scoop out of?
        And how to determine what size is "right" ?

    Any insights much appreciated....thanks in advance.

    Bob Pastorello, Oklahoma
    NSRCA 199, IMAC 1320, AMA 46373
    rcaerobob at cox.net
    www.rcaerobats.net

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.f3a.us/pipermail/nsrca-discussion/attachments/20030702/a91a319b/attachment.html