SERVO GEARS

[Jon Uhler]

Just a thought....

Can't you just rotate them around 180 degree's?  I thought I read that
somewhere......

-----Original Message-----
From: wgalligan [mailto:wgalligan at cnbcom.net]
Sent: Wednesday, April 16, 2003 2:17 PM
To: discussion at nsrca.org
Subject: Re: SERVO GEARS


They are getting fairly sloppy making lots of noise when engine is running.
Run them to 3/4 deflection and noise goes away they are that loose.
Thanks for the part #'s

Wayne

> JRPSG911 is the part number for the 911 gear sets...These are the proper
> gears to be using in the 9411 is converting to nylons.
> 
> The regular 9411 gears are fine....you don't need to change them until
they
> get sloppy...The metal gears on average will go over a hundred
> flights...where as the nylons I have seen go much longer....as in 200+
> flights without any noticeable wear.
> 
> If the 911 gears are out of stock the 9411 gears may be available  part #
> JRPSG9411
> 
> 
> I have run these servos a bunch..and the 9411's are a great Aileron
> solution.....Don't think just because they are metal gears they need to be
> changed out to nylons....I flew a set last year that was metal setup for
> most of the year...At the same time I was running nylon converted versions
> in another model....After the NATS I switched the metal ones to Nylon
> conversions.....
> 
> Performance is equal...life span of the gears is less with the metal gear
> servos all metal gear servos.
> 
> If you are down and out of flying look for a set of 9411 metal gears.
> 
> Sorry I don't have any gear sets at the moment.....
> 
> Troy Newman
> 
> 
> 
> ----- Original Message -----
> From: "wgalligan" <wgalligan at cnbcom.net>
> To: <discussion at nsrca.org>
> Sent: Wednesday, April 16, 2003 11:27 AM
> Subject: SERVO GEARS
> 
> 
> > Does anyone have any nylon servo gears that will fit in the JR9411 mid
> servo.  The metal gears in mine have gotten sloppy to the point of not
> trusting them.
> >
> > I ordered some several weeks ago but the LHD said they where on back
> order.
> > I need enough for two servos.   Will pay for them or replace them when
> mine come in.
> >
> > Thanks,
> > Wayne
> >
> > BTW WACO contest is 10 days away......
> > =====================================
> > # To be removed from this list, send a message to
> > # discussion-request at nsrca.org
> > # and put leave discussion on the first line of the body.
> > #
> >
> >
> =====================================
> # To be removed from this list, send a message to 
> # discussion-request at nsrca.org
> # and put leave discussion on the first line of the body.
> #
> 

=====================================
# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#

This transmission is intended only for the use of the addressee and may
contain information that is privileged, confidential, and exempt from
disclosure under applicable law. If you are not the intended recipient, or
the employee or agent responsible for delivering the message to the intended
recipient, this serves as notice to you that any dissemination,
distribution, or copying of this communication is strictly prohibited. If
you have received this communication in error please notify us immediately
via e-mail at the sender's e-mail address, delete this message from your
computer and/or computer network and destroy any hard copies that may have
been made. Thank you.
=====================================
# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#