Dingo users

[Tomanek, Wojtek]

Troy

Is surfacing the valve cover still a must, or recommended, I did surface
valve cover on my DZ and changed the valve cover gasket but not sure that
this is still critical like it was with L, FZ, SC, AC, SF (I think I got
them all <G>)

Wojtek  

	-----Original Message-----
	From:	Troy Newman [SMTP:tanewman at qwest.net]
	Sent:	Wednesday, September 11, 2002 11:51 AM
	To:	discussion at nsrca.org
	Subject:	Re: Dingo users

	Tom,

	Are you running too rich? The DZ doesn't run well rich...Its
something about raw fuel going in and putting out the fire. If the motor is
running too rich then it will shake like crazy and sound like its hammering
and banging around.....If you lean it out the motor will smooth out and be
awesome.....Needle valves vary but all the DZ's I have setup or seen run
seem to be at about (1) Turn open....In fact up here at elevation
5600-6000ft I'm only about ¾ of a turn open...The motor is still "rich" of
the peak by about 200-300rpm and runs great....
	You may look here for a solution rather than head shims.....I have
never heard of someone adding head shims to really solve a problem on this
motor...I have heard of people trying it and then they leaned the needle and
did not need it.
	Troy

	----- Original Message -----
	From:	"Tony Stillman" <tony at radiosouthrc.com
<mailto:tony at radiosouthrc.com> >
	To:	<discussion at nsrca.org <mailto:discussion at nsrca.org> >
	Sent:	Wednesday, September 11, 2002 7:01 AM
	Subject:	Re: Dingo users


		> Tom:
		>
		> I have used both.  The only problem we had with the 20% is
that the
	low-end
		> is too rich.  This can cause the engine to quit in
throttle-up.  The
	engine
		> makes so much power, you really don't need the 30%, but it
is necessary to
		> have good transition.
		>
		> I have not had to install any head shims on this engine,
and I don't know
	of
		> anyone that has had to either.
		>
		> I suggest you contact Richard Verano about the problem.
I'm sure he would
		> like to hear from you about any problems, as well as I'm
sure he will get
	it
		> fixed for you!
		>
		> Tony Stillman
		> Radio South, Inc.
		> 3702 N. Pace Blvd.
		> Pensacola, Fl 32505
		> www.radiosouthrc.com <http://www.radiosouthrc.com> 
		> 800-962-7802
		> ----- Original Message -----
		> From:	"Koenig, Tom" <Tom.Koenig at actewagl.com.au
<mailto:Tom.Koenig at actewagl.com.au> >
		> To:	"'discussion'" <discussion at nsrca.org
<mailto:discussion at nsrca.org> >
		> Sent:	Tuesday, September 10, 2002 7:07 PM
		> Subject:	Dingo users
		>
		>
			> > Hi all,
			> >
			> > another question to you fellow DZ guys.
			> >
			> > Those of you using the Coolpower heli fuel...are
you using the 30% or
	the
			> > 20% Nitro content. Did any of you using the 30%
find the need to
			> > de-compress??
			> >
			> > I'm finding the need to do so...just wondering
if any of you have
			> > experienced the same thing, hmmmmmm????
			> >
			> > I've also seen one suspected pump failure ( but
cannot validate this
		> sofar)
			> > on a friends engine. It is down by about 500
rpm, compared to his other
		> DZ,
			> > and makes a terrible rattling sound. Internal
inspection ( but not the
		> pump
			> > yet) has revealed nothing so far. Any one
seen/heard something similar?
			> >
			> > Thanks guys
			> >
			> > Tom
			> >
			> >
			> >
************************************************************************
			> > *PLEASE NOTE*  This email and any attachments
may
			> > be confidential. If received in error, please
delete all
			> > copies and advise the sender. The reproduction
or
			> > dissemination of this email or its attachments
is
			> > prohibited without the consent of the sender.
			> >
			> > WARNING RE VIRUSES:  Our computer systems sweep
			> > outgoing email to guard against viruses, but no
warranty
			> > is given that this email or its attachments are
virus free.
			> > Before opening or using attachments, please
check for
			> > viruses.  Our liability is limited to the
re-supply of any
			> > affected attachments.
			> >
			> > Any views expressed in this message are those of
the
			> > individual sender, except where the sender
expressly,
			> > and with authority, states them to be the views
of the
			> > organisation.
			> >
************************************************************************
			> >
			> >
			> > ====================================
			> > # To be removed from this list, send a message
to
			> > # discussion-request at nsrca.org
<mailto:discussion-request at nsrca.org> 
			> > # and put leave discussion on the first line of
the body.
			> > #
			> >
			> >
		>
		>
		> ====================================
		> # To be removed from this list, send a message to
		> # discussion-request at nsrca.org
<mailto:discussion-request at nsrca.org> 
		> # and put leave discussion on the first line of the body.
		> #
		>
		>

	====================================
	# To be removed from this list, send a message to #
discussion-request at nsrca.org <mailto:discussion-request at nsrca.org>  # and
put leave discussion on the first line of the body.
	#
==================# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#