- Webra 145 AAR

[Keith Black]

You may need to back off the pump pressure a bit. I have a Bully 1.45
(basically same as Webra) that ran terrible and blew a ton of fuel out until
I unscrewed the pump screw 3/4 turn. This made a huge difference it the way
mine ran!  I could probably still go out another 1/4 turn.

Of course this may also depend on the position of your tank, orientation of
motor, etc.

Good luck,
Keith

----- Original Message -----
From: "Rodney Tanner" <rtanner at bbbeurorscg.com.mx>
To: <discussion at nsrca.org>
Sent: Monday, November 04, 2002 11:18 AM
Subject: Re: - Webra 145 AAR


> Jim, Lee or any one else using the Webra 145 AAR. . . .
> I have a new engine that I am still running in - four clicks rich. It
seems
> to be venting a lot of raw fuel from the carb. Is that normal, given the
> rich needle setting. I have checked the fuel lines etc. and everything
seems
> in order. .
> Any comments would be appreciated
> Rodney
> NSRCA 2906
>
>
>
>
> on 4/11/02 10:17 AM, Woodward James R Civ 416 FLTS/TPS at
> James.Woodward2 at edwards.af.mil wrote:
>
> > Despite two minor crashes, and a "accidental" competitor induced stab
total
> > break-out, I've managed to keep my prototype together!  I have Ken
Blackwell
> > (who also is on the list) to sincerely thank for his trust many months
ago,
> > regarding his design and my involvement with it.
> > Jim W.
> >
> > -----Original Message-----
> > From: Jeff Hughes [mailto:jhughes at hsonline.net]
> > Sent: Monday, November 04, 2002 8:15 AM
> > To: discussion at nsrca.org; 'discussion at nsrca.org'
> > Subject: Re: - Brace yourself!!! 2-cycle pipes and coupler material
> >
> >
> >
> > Hey, how come you have a Phase One, and I was told they are not
> > available till spring?
> >
> >
> >> Hey Folks
> >>
> >> - Brace yourself!  Those of you that think the most expensive option
> > for
> >> equipment is best, you may want to sit down.  This weekend I flew my
> > Phase
> >> One with Webra 1.45 R and replaced my very expensive ES 2 cycle pipe
> > with
> >> 0.9" inlet, with the less expensive Greve pipe.  On the ground, the
> > engine
> >> seemed to run up a little better.  This engine has about 300 flights
> > on it.
> >> In the air, it was acting like a new engine again!!!!!!!!!!  This was
> > a VERY
> >> pleasent surprise, as the power was 'not-what-it-used-to-be'
> >> (understandably).  Still using the 17 x 12 APC (regular blade).
> >> Additionally, the "hickup" that was present when throttleing from
> > inverted
> >> that was a pain with the ES setup, is now gone.  For instance, when
> > pushing
> >> around the bottom of the cuban 8 with 2/4, thottle is smooth without
> >> hessitation.  Same with exit of the triangle loop, and exit of the 3
> > turn
> >> spin. - very happy customer.  This was the same pipe I tried first on
> > my
> >> Advantage.  That setup, I used the "full-length" MACs header, 1/4 -
> > 3/8"
> >> gap, and the "full-length pipe".  That was about 1.5-2.0" longer than
> > the
> >> 27.5" setup length on Piedmonts website.  Setup ran perfectly.  On
> > the Phase
> >> One setup, I used the 27.5" setting by cutting down the header, with
> > equally
> >> good performance.  I will attribute any extra performance on the
> > Advantage
> >> due to it's using the new Webra AAR.  The design of the pipe does not
> > lend
> >> to cutting anything from the pipe (... wouldn't recommend that
> > approach).
> >> The whole setup fit with some room to spare in the Phase One.
> >>
> >> I'm getting away from a kick of reading rpm of reading on the ground
> > (after
> >> some reading about pipe theory).  Readings show that max "air"
> > performance
> >> is gained by getting the pipes peak performance on the ground, and
> >> lengthening the setup to about 300 rpms less.  Then, it unloads in
> > the air
> >> and has more sustained power in the uplines.
> >>
> >> Header coupler material:  Tired of having your Aerotrend replacement
> >> silicone tubing crack and break too quickly?  www.mcmaster.com has
> >> "silicone" replacement tubing.  I ordered some off of Bob P.'s
> >> recommendation.  I ordered 2' each of "clear-medical" silicone,
> > and "red"
> >> silicone tubing.  The material seems very good.  Total cost including
> >> shipping was $18.00.  The red feels lighter.  Both seem durable and
> > plyable
> >> - similiar to the material that Macs headers come with.
> >>
> >> Jim W.
> >> =====================================
> >> # To be removed from this list, send a message to
> >> # discussion-request at nsrca.org
> >> # and put leave discussion on the first line of the body.
> >> #
> >>
> >>
>
> =====================================
> # To be removed from this list, send a message to
> # discussion-request at nsrca.org
> # and put leave discussion on the first line of the body.
> #
>

=====================================
# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#